BIOS Settings
Introduction
The BIOS or Basic Input/Output System is the basic controller that allows all of the components that make up a computer system to talk to one another. But in order for this to happen, there are a number of things that the BIOS needs to know how to do. This is why the settings within the BIOS are so critical to the operation of the computer system. For about 95% of the computer users out there, they will never need to adjust the BIOS settings of their computer. However, those who have chosen to build their own computer system will need to know how to modify the settings.
Some of the critical things one will need to know are the clock settings, memory timing, boot order and drive settings. Thankfully the computer BIOS has come a long way in the past ten years where many of these settings are automatic and very little needs to be adjusted.
How to Access the BIOS
The method for accessing the BIOS is going to be dependent upon the manufacturer of the motherboard and the BIOS vender they have selected. The actual process to get to the BIOS is identical, just the key that is needed to be pressed will vary. It is important to have the user manual for the motherboard handy whenever changes will be made to the BIOS.
The first step is to look up what key needs to be pressed to enter the BIOS. Some of the common keys used to access the BIOS are F1, F2 and the Del key. Generally the motherboard will post this information when the computer first turns on, but it is best to look it up before hand. Next, power on the computer system and press the key to enter the BIOS after the beep for a clean POST is signaled. I will often press the key a couple times to make sure it registered. If the procedure has been done correctly, the BIOS screen should be displayed rather than the typical boot screen.
CPU Clock
The very first setting that needs to be made in the BIOS is to adjust the motherboard to utilizing the proper clock settings for the CPU installed in the computer. Most modern BIOS vendors can detect the type of CPU and automatically set the proper timings. Refer to the documentation from the CPU and motherboard vendor for the proper settings.
The CPU speed is comprised of two numbers, a bus speed and a multiplier. The bus speed is the tricky part because vendors may have this setting done either at the natural clock rate or at the enhanced clock rate. The natural front side bus is the more common of the two. The multiplier is then used to determine the final clock speed based on the bus speed of the processor. Set this to the appropriate multiple for the final clock speed of the processor.
For an example, if you have an AMD Athlon XP 2500+ processor that has a CPU speed of 1.82GHz clock, the proper settings for the BIOS would be a bus speed of 166MHz and a multiplier of 11. (166MHz x 11 = 1.826 GHz)
Memory Timings
The next aspect of the BIOS that needs adjusting is the memory timings. Typically it is not necessary for this to be done if the BIOS can detect the settings from the SPD on the memory modules. In fact, if the BIOS has a SPD setting for the memory, this should be used for the highest stability with the computer. Other than this, the memory bus is the setting you will likely need to set. Verifying that the memory bus is set to the appropriate speed for the memory. This may be listed as the actual MHZ speed rating or it may be a percentage of the bus speed. Check with your motherboard manual about the proper methods for setting the timings for memory.
Next Page – Boot Order, Drives and Clearing CMOS – Page 1, 2
Incoming search terms for the article:
Similar articles
- EXTREME Overclocking
CPU Over Clocking Date Article Written: July 23, 2000 Written By: Mark Torres So you have a need for speed huh? You could go out and buy a new processor, or you could simply over clock your existing one. Well that is all well and good, once you consider a few things. One,
... - How to increase the speed of my computer?
First of all check the minimum size of virtual memory (Here the path: Start – Settings – Control Panel – System – Perfomance – Virtual Memory, field ‘Minimum’). This value must be at least two times (better three times) higher than ammount of RAM. For example if you have 32Mb of RAM the optimal size
... - Understanding CPU Overclocking
While the words CPU and microprocessor are used interchangeably, in the world of personal computers (PC), a microprocessor is actually a silicon chip that contains a CPU. At the heart of all personal computers sits a microprocessor that controls the logic of almost all digital devices, from clock radios to fuel-injection systems for
... - How to Speed up Your RAM : Introduction
It’s official: DDR400 memory is now the formal standard. Now that the Jedec committee has made its decision, RAM and motherboard makers finally have some guidelines on integration. DDR400, a.k.a. PC3200 RAM, had been plagued by incompatibility issues and an embarrassing lack of performance improvements. Without any official standard at all, trying to find
... - Front-side bus
From Wikipedia, the free encyclopedia This article does not cite any references or sources. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2008) In personal computers, the front-side bus (FSB) is the bus that carries data between the CPU and the northbridge. Depending on
...