Performance optimization
Performance optimization – a How to for XP Diy-Computer-Repair can help! Performance optimization, what is it? Should I do it? How would I do it?
Good questions and very few answers on the internet. There is a lot of advice out there on how to optimize your computer’s Operating System (OS) from uninstalling unused programs to running anti-virus software.
So my advice? Glad you asked!
Performance optimization begins with realizing your computer isn’t as fast as it was when you turned it on the first time. This is normal. Different things will slow your computer down, too many files on the hard drive, too many ‘utilities’ running when you start, not enough memory for the programs to run properly.
Your computer should be able to run five of the top software programs simultaneously. I am not joking! You should be able to have these types of programs running while you do something else: email, browser, word processor, spread sheet, and a graphics program. Right now while I am building this web page (typing it up and formatting it) I have these programs running on the desktop: 2 separate Internet Explorer 7′s, a RSS reader, email, notepad, and Front Page. My system is responding like it should, not dragging or hesitating. ( I also have four separate versions of explorer open for different folders). My screen resolution is set for 1278 x 1024.
How do I do this with a P4 2.5 GHz -M processor and 2 gig of ram (note the processor speed, it is 1/2 the speed of the latest and greatest!)?
Performance optimization!
Ok, so how do I optimize my system? By keeping it clean and making the OS do what I want it to do not what the programmers think it should do.
Temporary files , temp files are files that your word processor, IE, Firefox, and other programs created for their purpose. They should delete them when you close them but they don’t. So first we tell the OS where we want the temp files to be then we delete those others. (Note: After restart you can delete the temp files but not until then. You will need to do a search for folders named Temp to find them all )
We need to build a new place for all those temporary files. If you have two volumes then I would suggest you put them on the second drive not the OS or system drive. 
Second we need to tell the OS where we want to put temp files, this is done through the system properties pages.
Right click on My Computer and click on the properties or go to the control panel and open System. Go to the Advanced tab, on the Advanced tab we will use these sections: Performance, Startup and Recovery, and Environment Variables .
Environment Variables: 
When the page opens you will see two windows. The top window is for the current user, the bottom window is for the System.
Once you have created your new temp folder (I use D:\Temp on the D: drive) then click each line and change it to where your new Temp folder is located. (Note: Current user temp folder will have to be modified for each user of the system if others use your computer).
In the System variables window we need to change three lines:
Path: double click on the value, go to the end of the line and add to the path to your new temp folder like this: ;D:\Temp Note the ; before the D:\ (putting the temp in the path line will force all programs to use the temp folder, such as an install program).
Next scroll down to TEMP and double click the value and put in your new path to the temp folder, do the same for the TMP value.
These changes do not take effect until after you restart, complete your optimization before restarting.
Performance: 
First: Visual Effects, I adjust for best performance, if you want to use custom and select a few will not impact performance but the ‘Let windows choose….’ will definitely cause performance to degrade.
Second: Click on Advanced, go to Virtual Memory, click on the ‘Change’ button. (First let me explain something about the ‘Virtual Memory or Swap File’, this is a file where any time you open or use more memory than the physical memory installed in the system is put
temporarily. That is to say you have 512 meg of physical ram installed. Once you open enough programs that the memory usage goes past the 512 Meg of ram then the OS will start to move unused programs from physical memory to the swap file. Now there is no hard rule on how much space you give this swap file, from my experience it is around 1.5 times the physical memory. Once you go past 2 gig then it takes to long to read and write the swap file every time something is swapped from ram to the file or from the file to ram regardless of the processor speed. If you have more than
2 gig of physical memory in your system you will need to spread the swap file across more drives, you can only have one swap file per drive. The only systems I have worked on that this was not valid were servers with more than four processors.)
To set your ‘Virtual Memory’ select the drive, then put in the ‘Initial size’ (the size of your physical memory, then in the ‘Maximum size’ put in 1.5 times that. Set the second drive (D:) file sizes, then modify the fist drive (C:) (normally I remove the swap file from the C: drive) then close the page, if you get the, ‘System needs to be restarted’ message click ok, it will not restart yet.
Startup and Recovery:
This one is a personal type tweak. What I mean is you do not 
need to do anything here unless you remove the swap file from the C: drive. If you remove the swap file from the C: drive you will get a warning that the system can not write a Dump file for zero bytes.
Under the System failure heading I remove all check boxes, I also select (none) for Write debugging information. The reason is that unless you suspect that you have an unstable system it only creates more overhead for the system to read at startup.
The idea of optimizing your memory usage is to keep the system memory at it’s lowest point and keep all programs in the physical ram vs. swapping them out to the hard drive.
Fix It! Your DIY Computer Repair Newsletter! Click here to get your copy of Fix It!
Internet Explorer:
This is the last tweak before restart. on the desktop icon for Internet Explorer right click and go to properties, on the ‘Browsing history’ heading click on Settings.
You can control how much disk space is used on this page, I set mine to 10 meg. At the bottom of the page you can change how many days the history will keep, select what you feel is appropriate for your use. Then click on the button ‘Move folder…’ browse to your temp folder. Once you close the properties pages you will automatically be logged off, once you log back on you still need to restart your computer to complete the other settings you have changed.
Want to know more? There are more ways to optimize your system to regain some of that memory that is wasted by non essential programs, visual effects, and services here: More…Performance optimization or in the Self Computer Repair E-Book.
Are you a member? Does your Computer need some TLC?There is a lot more information on performance optimization in the DIY Membership Section!
Q and A This site contains a lot of information. As with any publication not all information is available due to space, time, or subject constraints.
If you have a question that you did not find the answer on this web site you a can ask your question here and we will endeavor to get you the most up to date answer possible!
Free Stuff!
Thank you for visiting my web site, and please come back again .
Return to previous page
This website is not intended for children under the age of 18
Home Support About owner Site Map Why I use SBIPrivacy Policy Disclaimer
Return to top
Incoming search terms for the article:
Similar articles
- Speed up and Tune Your Hard Drive’s Performance How To
Defragmenting Your Disk: Fragmentation occurs when you add and remove files from your computer. When you delete a file, Windows marks the sectors as available, and uses them the next time you create a file. If a file gets larger and contiguous space isn’t available, Windows uses other available sectors to store the
... - Memory (RAM) and its influence on performance
Memory (RAM) and its influence on performance It’s been proven that adding more memory to a computer system increases its performance. If there isn’t enough room in memory for all the information the CPU needs, the computer has to set up what’s known as a virtual memory file. In so doing, the CPU
... - PC running VERY VERY SLOW
>> Item 6 in this list might be worth checking first, but answer the others as appropriate if it doesn’t apply. >> And post that Scanlog as well. 0 > when did the problem seem to be begin? 1 > is it very slow to boot up? 2 > do programs
... - Improve Its Performance
So is your computer extremely slow? Are you wasting more time waiting then you are actually working? This can be completely frustrating and at one time or another all computer users will experience their computer being extremely slow. Fortunately there are some things that you can do to fix a slow computer. When you first
... - Is your Computer Extremely Slow? Here Are Some Tips To Improve Its Performance
So is your computer extremely slow? Are you wasting more time waiting then you are actually working? This can be completely frustrating and at one time or another all computer users will experience their computer being extremely slow. Fortunately there are some things that you can do to fix a slow computer. When
...